Key Takeaways
Here's the short version if you're planning a weekend build:
-
An upholstered headboard is a plywood or MDF board covered with foam, batting and fabric, then mounted to the wall or bed frame.
-
Panels usually run 2 to 4 inches wider than the mattress, with the top sitting 48 to 60 inches above the floor.
-
Two-inch medium firm foam is a comfortable starting point. A twin needs one 24 x 82 inch foam sheet; full, queen and king panels need two.
-
Batting should wrap 4 to 6 inches past every edge.
-
Drill holes for buttons before the foam goes on if you want tufting.
-
A French cleat is the sturdiest way to hang a wall mounted headboard.
Learning how to make a headboard comes down to four layers: a wood board, foam, batting and fabric. You cut the board, glue on the foam, wrap it in batting, pull the fabric tight and staple it to the back, then mount the finished headboard to the wall or bed frame. Most people finish a diy headboard like this in a weekend with basic tools, which makes it a good guest bedroom project before holiday visitors arrive.
This guide covers sizing tips, choosing foam for headboard padding, the full upholstery process, tufting and mounting. Midwest Fabrics has supplied upholstery materials to DIY customers and professional upholsterers since 1983, and the foam counts below use the real sheet sizes we carry.
Materials and Basic Tools for a DIY Headboard
The list is short. Quantities below are for a queen headboard about 64 inches wide and 42 inches tall, the most common diy upholstered headboard size.
|
Item |
Queen Quantity |
Notes |
|
3/4-inch plywood or MDF |
1 sheet (4 x 8 feet) |
Covers any size bed up to king |
|
Foam, 2 x 24 x 82 inches |
2 sheets |
Medium firm is best for leaning |
|
Upholstery batting |
About 2 1/2 yards |
Wraps 4 to 6 inches past each edge |
|
Upholstery fabric |
About 2 1/2 yards |
Check bolt width against panel height |
|
Spray adhesive |
1 can |
Bonds the foam to the wood |
|
Staples, screws, wood glue |
1 box each |
For the fabric and mounting strips |
|
French cleat or 1x4 legs |
1 set |
Wall or bed frame mounting |
You'll also need a tape measure, a circular saw (or have the lumberyard cut the wood), a drill, scissors, an electric knife for foam and a staple gun. A manual staple gun works, but a pneumatic upholstery staple gun drives staples flush through fabric and batting with far less effort.
Headboard Size Chart by Bed Width
Getting the headboard size right starts with the mattress. Make the headboard 2 to 4 inches wider so the fabric edge doesn't disappear behind the bedding.
|
Bed Size |
Mattress Width |
Panel Width |
Panel Height |
Foam Sheets (24 x 82 in.) |
|
Twin |
38 in. |
41 in. |
36 to 48 in. |
1 (cut in half) |
|
Full |
54 in. |
56 to 58 in. |
36 to 48 in. |
2 |
|
Queen |
60 in. |
62 to 64 in. |
36 to 48 in. |
2 |
|
King |
76 in. |
78 to 80 in. |
36 to 48 in. |
2 |
Standard headboard heights land between 48 and 60 inches above the floor, so measure from the floor to the top of your mattress and add the visible panel height you want. On a queen bed with a 24-inch-tall mattress, a 42-inch DIY headboard that tucks a few inches behind the mattress finishes in the middle of that range.
The foam math is simple. Each sheet is 24 inches wide and 82 inches long, so two sheets stacked lengthwise give 48 inches of height and enough length for a king. One sheet cut in half covers a twin.
DIY King Headboard Sizing
A diy king headboard is the same build, just wider and heavier. An 80 x 42 inch headboard still fits on one 4 x 8 sheet of plywood, and the 82-inch foam length covers the full width with no seam up the face. Grab a helper for stretching the fabric and hanging the headboard, and run the cleat almost the full width so the weight spreads across several wall studs.
What Is the Best Material for a Headboard?
Match each layer of a DIY headboard to its job: the board holds staples, the foam gives comfort and the fabric takes the wear.
-
Board. Half-inch or 3/4-inch plywood holds staples well right up to the edge and stays light enough to hang. MDF is flatter but heavier, and its edges can crumble when you staple close to them.
-
Foam. Foam should be at least 2 inches thick for comfort. We'd start with 2-inch HR30 medium firm, which gives when you sit up against pillows but holds its shape. HR60 extra firm feels closer to a padded wall. Our foam density chart explains how firmness ratings compare, and the upholstery foam collection has thinner sheets for a slimmer padded headboard.
-
Fabric. Use upholstery fabric rather than quilting cotton. It's heavier and won't show every staple line once you pull it tight. Browse upholstery fabric and check the bolt width: a 54-inch bolt run sideways covers a headboard up to about 42 inches tall. Navy blue velvet gives a glamorous look, a plaid suits a cabin bedroom, and a linen-look weave fits farmhouse style.
How to Make a Headboard Step by Step
This method works for any diy fabric headboard, plain or tufted, and takes about an afternoon of hands-on time.
1. Measure and Cut the Board
Mark the size from the chart with a tape measure and cut with a circular saw. For a softer shape, round the top corners with a jigsaw or trace an arch or half moon. Sand the edges so nothing snags the batting.
2. Drill Holes for Buttons (Tufting Only)
If you plan to tuft, mark your button grid and drill now. Drilling holes after the foam goes on is messy and less accurate.
3. Glue the Foam to the Board
Spray adhesive on the board and the back of the foam, wait until both feel tacky, then lay the foam down and push it flat. On larger headboards, butt the two sheets together across the middle with no gap. Trim flush with an electric knife.
4. Wrap the Batting
Place the headboard foam side down on the batting and wrap it 4 to 6 inches around to the back side. Staple it every few inches, then trim the excess wadding so it doesn't bunch at the corners. Batting hides the foam seam and gives the face a professional look.
5. Stretch and Staple the Fabric
Lay the fabric face down, check that any pattern runs straight, and center the headboard on it. Staple the middle of the top edge, pull fabric tight and staple the middle of the bottom, then repeat on each side. Work outward toward the corners with staples about 2 inches apart.
Pull the fabric firmly and evenly. Too little tension leaves the headboard wrinkled, and too much pulls a stripe out of line. Fold the corners like a wrapped gift, staple the folds flat and cut away the excess fabric.

6. Mount the Finished Headboard
For a wall mounted headboard, rip a 1x4 lengthwise at 45 degrees, attach one half to the back of the headboard piece with wood glue and screws, and screw the other half into the wall studs so the angles hook together. To use an existing bed frame instead, screw two furring strips vertically to the back as legs, drill holes to match the frame brackets, and bolt them on.
How to Make a DIY Tufted Headboard
A diy tufted headboard adds a few hours, mostly planning, and it's the most popular DIY headboard upgrade. Before step 3, mark a diamond grid with the outer holes about 4 inches from the edges and corners, and drill a 1/4-inch hole at each mark.
After the fabric is on, push each button prong through the fabric and foam until it comes out the back, then spread the prongs flat. The buttons and prongs collection carries upholstery buttons for this. Medium firm foam 2 to 3 inches thick lets each button sink into a deeper dimple.
How to Reupholster a Headboard
If your old headboard has a solid frame, how to reupholster a headboard is mostly a teardown. Pry out the old staples, peel off the fabric and use it as a pattern. Press on the foam: if it stays flat or crumbles, replace it. Then follow steps 4 through 6 to secure the new cover.
Does It Cost Less to Make Your Own Headboard?
Usually, yes. Building your own DIY headboard means you pay for materials, not a retail markup or freight on a bulky headboard.
|
Material |
Cost Impact |
Ways to Spend Less |
|
Fabric |
High |
Pick a solid weave or a closeout bolt |
|
Foam |
Medium to high |
Use 1-inch foam with thick batting |
|
Plywood |
Medium |
Use 1/2-inch plywood for twin and full |
|
Batting and staples |
Low |
Buy batting by the yard |
|
Mounting hardware |
Low |
Bolt to the bed you already have |